Community Theater Green Room Discussion Board: Paint for latex?

Author

Message

Kurtin
Player
Player

Joined: 6/03/09
Online Status: Offline
Posts: 21

Topic: Paint for latex?
Posted: 8/11/09 at 3:50am

Hi guys. I've made a skeleton prop by brushing latex over tissue paper laid over a childrens' plastic educational skeleton.

It looks flakey enough, the latex looks like dessicated skin, but I want to colour it a bit blackish/green to make it look more realistic. I have an airbrush kit, but I don't know of any paint that will stick to latex.

The prop won't be moved, except to position it for the shot, (this is for a film, btw), so it doesn't have to be super durable. But I would like it to at least stay put and not crack for the weeks of shooting.

Can you guys suggest anything appropriate, and not too expensive?

Thanks,

Kurt

IP Logged

Gaafa
Celebrity

Joined: 3/21/04
Location: Australia
Online Status: Offline
Posts: 1181

Posted: 8/11/09 at 8:20pm

I would imagine any 'plastic' [latex] paint, would do the job.

Joe
Western Gondawandaland
turn right @ Perth.
Hear the light & see the sound.
Toi Toi Toi Chookas {{"chook [chicken] it is"}
May you always play
to a full house}

IP Logged

Kurtin
Player
Player

Joined: 6/03/09
Online Status: Offline
Posts: 21

Posted: 8/11/09 at 8:50pm

Yeah, Gaafa, it would stick alright, but I'm not sure if it would stay on and nor crack after a bit of handling. I need something that will not look like crazed paint after a few weeks.

IP Logged

kries13
Player
Player

Joined: 8/12/09
Location: United States
Online Status: Offline
Posts: 18

Posted: 8/12/09 at 3:36pm

My suggestion would be to do a tinting or glazing of the latex you have already applied. You can do this by watering down a couple of other colors and dabbing on in the skeleton as it exists now. You could use a sponge to control the amount of glaze going onto the surface - and be sure to go more heavily into crevice areas as this will lend itself to the aged look I think you are desiring.

You could also use tea to stain the latex.

If you used a flat based latex the glaze will work very well. If it was a gloss surface then you will want to be more careful when wiping off the glaze as it will come off more easily.

Good luck - sounds like a fun project!

kries
I art therefore I am.
www.artisrelative.com

IP Logged

Gaafa
Celebrity

Joined: 3/21/04
Location: Australia
Online Status: Offline
Posts: 1181

Posted: 8/12/09 at 7:03pm

Just add some Aquadhere [white wood glue] to the paint, which will withstand any amout of handling. Much the same as I do, when I'm painting the stage deck. The glue dries clear & the same colour as the plastic paint, thus bonding the surface resisting wear or scuffs.

Joe
Western Gondawandaland
turn right @ Perth.
Hear the light & see the sound.
Toi Toi Toi Chookas {{"chook [chicken] it is"}
May you always play
to a full house}

IP Logged

Kurtin
Player
Player

Joined: 6/03/09
Online Status: Offline
Posts: 21

Posted: 8/12/09 at 7:45pm

That's an idea, kries. The latex has dried quite a dark yellowish-brown. I would need to mix a darker colour to lay over it.

It's also a tad glossy, like smooth rubber in places, so a matte finish paint would be good to tone that down.

I'll test that, and see how I go.

The skeleton is looking pretty gruesome as it is, but I want it to look more horrible. Trouble is, my little granddaughter watches me working on it and it doesn't scare her a bit!

IP Logged

Kurtin
Player
Player

Joined: 6/03/09
Online Status: Offline
Posts: 21

Posted: 8/12/09 at 7:47pm

Never thought of Aquadhere, Gaafa. I wonder if it would make the paint stick better, or just make it more easy to peel off in one piece?

Trouble with aquadhere is it tends to dry a bit glossy. But then, it all depends on relative quantities, I suppose.

I'll do some tests.

Thanks.

IP Logged

Props, Scenery, Costumes and Makeup
Community Theater Green Room Discussion Board :Producing Theater :Props, Scenery, Costumes and Makeup

Author	Message
Kurtin Player Joined: 6/03/09 Online Status: Offline Posts: 21	Topic: Paint for latex? Posted: 8/11/09 at 3:50am
	Hi guys. I've made a skeleton prop by brushing latex over tissue paper laid over a childrens' plastic educational skeleton. It looks flakey enough, the latex looks like dessicated skin, but I want to colour it a bit blackish/green to make it look more realistic. I have an airbrush kit, but I don't know of any paint that will stick to latex. The prop won't be moved, except to position it for the shot, (this is for a film, btw), so it doesn't have to be super durable. But I would like it to at least stay put and not crack for the weeks of shooting. Can you guys suggest anything appropriate, and not too expensive? Thanks, Kurt

	IP Logged

Gaafa Celebrity Joined: 3/21/04 Location: Australia Online Status: Offline Posts: 1181	Posted: 8/11/09 at 8:20pm
	I would imagine any 'plastic' [latex] paint, would do the job.
	Joe Western Gondawandaland turn right @ Perth. Hear the light & see the sound. Toi Toi Toi Chookas {{"chook [chicken] it is"} May you always play to a full house}
	IP Logged

Kurtin Player Joined: 6/03/09 Online Status: Offline Posts: 21	Posted: 8/11/09 at 8:50pm
	Yeah, Gaafa, it would stick alright, but I'm not sure if it would stay on and nor crack after a bit of handling. I need something that will not look like crazed paint after a few weeks.
	IP Logged

kries13 Player Joined: 8/12/09 Location: United States Online Status: Offline Posts: 18	Posted: 8/12/09 at 3:36pm
	My suggestion would be to do a tinting or glazing of the latex you have already applied. You can do this by watering down a couple of other colors and dabbing on in the skeleton as it exists now. You could use a sponge to control the amount of glaze going onto the surface - and be sure to go more heavily into crevice areas as this will lend itself to the aged look I think you are desiring. You could also use tea to stain the latex. If you used a flat based latex the glaze will work very well. If it was a gloss surface then you will want to be more careful when wiping off the glaze as it will come off more easily. Good luck - sounds like a fun project!
	kries I art therefore I am. www.artisrelative.com
	IP Logged

Gaafa Celebrity Joined: 3/21/04 Location: Australia Online Status: Offline Posts: 1181	Posted: 8/12/09 at 7:03pm
	Just add some Aquadhere [white wood glue] to the paint, which will withstand any amout of handling. Much the same as I do, when I'm painting the stage deck. The glue dries clear & the same colour as the plastic paint, thus bonding the surface resisting wear or scuffs.
	Joe Western Gondawandaland turn right @ Perth. Hear the light & see the sound. Toi Toi Toi Chookas {{"chook [chicken] it is"} May you always play to a full house}
	IP Logged

Kurtin Player Joined: 6/03/09 Online Status: Offline Posts: 21	Posted: 8/12/09 at 7:45pm
	That's an idea, kries. The latex has dried quite a dark yellowish-brown. I would need to mix a darker colour to lay over it. It's also a tad glossy, like smooth rubber in places, so a matte finish paint would be good to tone that down. I'll test that, and see how I go. The skeleton is looking pretty gruesome as it is, but I want it to look more horrible. Trouble is, my little granddaughter watches me working on it and it doesn't scare her a bit!
	IP Logged

Kurtin Player Joined: 6/03/09 Online Status: Offline Posts: 21	Posted: 8/12/09 at 7:47pm
	Never thought of Aquadhere, Gaafa. I wonder if it would make the paint stick better, or just make it more easy to peel off in one piece? Trouble with aquadhere is it tends to dry a bit glossy. But then, it all depends on relative quantities, I suppose. I'll do some tests. Thanks.
	IP Logged

Topic: Paint for latex?( Topic Closed)